Supported devices
Browsing the devicetree, editing node properties and generating the overlay work on every board, whatever its vendor.
Two parts of the Devicetree Manager depend on the chip family:
- Pin configuration: the chip view and its Functions panel. See Pin configuration.
- Clocks: the Clocks view. See Clock configuration.
In the table:
- Yes: it works.
- Partial: it works, without what the note says.
- No: the view says the board is not supported. The rest of the manager keeps working.
| Vendor | Family | Pin configuration | Clocks |
|---|---|---|---|
| STMicroelectronics | STM32 C0, F0, F2, F3, F4, F7, G0, G4, H5, L0, L1, L4, L5, U0, U3, U5, WB, WBA, WL | Yes | Yes |
| STM32 H7 | Yes | Partial (note 1) | |
| STM32 F1 | No | Yes | |
| STM32 C5, H7RS, N6, WB0, WL3 | Yes | No | |
| STM32 MP1, MP13, MP2 | Yes | No | |
| Silicon Labs | Series 2 (xG21 to xG29, BGM and MGM modules) | Yes | Yes |
| Series 3 (SiXG301) | No | Yes | |
| Series 0 and 1, SiWx91x | No | No | |
| NXP | MCX N, A, C and W | Yes | No |
| Kinetis KE1x (KE14Z, KE15Z, KE16Z, KE17Z, KE14F, KE16F, KE18F) | Yes | Partial (note 2) | |
| Kinetis K, KL, KV, KW and K32L | Yes | No (note 3) | |
| S32K1 | Yes | No | |
| LPC51U68, LPC54114, LPC55 | Yes | No | |
| i.MX RT, i.MX, RW61x, S32K3 | No | No | |
| Microchip | SAM D2x, D5x, E5x, C2x, L2x, R2x, R3x, SAM3, SAM4, SAM E7x, V7x and PIC32C | Yes | No |
| SAMA7 | No | No | |
| Espressif | ESP32, ESP32-S2, S3, C2, C3, C5, C6 and H2 | Yes | No |
| Renesas | RA (RA2, RA4, RA6, RA8) and RA0 | Yes (note 4) | Yes |
| RZ, RX, SmartBond | No | No | |
| Infineon | PSoC 4, PSoC 6, PSoC Control C3, CYW20829, XMC7000, TRAVEO T2G, PSoC Edge | Yes | No |
| XMC4500, XMC4700 | Partial (note 5) | No | |
| Older PSoC 6 kits (CY8CKIT-062-BLE, CY8CKIT-062-WIFI-BT) | No | No | |
| Texas Instruments | MSPM0 G and L | Partial (note 6) | Yes (note 7) |
| MSPM33C | Partial (notes 6 and 8) | Yes (note 8) | |
| CC13xx, CC26xx | Partial (note 9) | No (note 10) | |
| CC23x0, CC32xx | Yes | No (note 10) | |
| AM13E | Partial (note 11) | No | |
| Sitara AM6x and Jacinto (K3), Tiva C, MSP432 | No | No | |
| Nordic | nRF | No | No |
| Others | No | No |
Notes:
- STM32 H7: the view does not check the PLL input and VCO ranges. Zephyr 4.5 checks them when the board starts, and its clock setup fails when a PLL is outside them.
- Kinetis KE1x: a KE1xZ peripheral whose clock source is the LPFLL shows no frequency.
- Kinetis K, KL, KV, KW, K32L: the PLL is set in Kconfig, not in the devicetree, so the view can't show the clock tree.
- Renesas: the chip view asks you to install Renesas's pin data once (click Install).
- Infineon XMC4: the functions come from Zephyr's pin table. Functions only Infineon's XMCLib lists, such as the USIC chip-select outputs, are not offered.
- TI MSPM0 and MSPM33C: the build does not say the package, so the chip view shows every pin of the part's series.
- TI MSPM0 clocks: from Zephyr 4.4. On Zephyr 4.2 and 4.3 the clock tree has another shape, and the view says the board has no clock tree.
- TI MSPM33C: pins and clocks need the Zephyr release after 4.5. Zephyr 4.5 has no pin table and no clock tree for it.
- TI CC13xx and CC26xx: the build does not say which DIOs the package has, so the chip view shows DIO0 to DIO31.
- TI CC13xx, CC26xx, CC23x0 and CC32xx clocks: the devicetree has one fixed system clock. The view shows it with the peripherals on it, with nothing to change or check.
- TI AM13E: it uses the MSPM0 pin controller, so the chip view shows its pins and functions, from TI's pin file. It is not tested on a board that routes pins.
The vendor pages under Pin configuration say what each vendor's pin configuration sets and checks.
To request a family, or to contribute one, open an issue or a pull request on the companion extension's GitHub repository.